![[Flo-Products Company Logo]](images/fplogo1.gif)
|
|
|
DIN, ISO, MINI, Sub-Micro
and Adapters are available from this manufacturer: |
Canfield Connector |
 |
Series 5000 Solenoid Valve ConnectorsThe MINI and ISO connectors are made according to DIN 43650 / ISO 4400. They are used as protective enclosures for electrical connection in conjunction with hydraulic and pneumatic solenoid valves. These connectors offer distinct advantages over "hardwired" solenoid valves because of their modular design. Used where rapid installation and service are a must. Better than molded construction when special wire is needed or when using one long wire run.MINI ConnectorThe Canfield Connector field wireable MINI solenoid valve connector is a high quality interconnection device for use with solenoid valves and pressure switches. The connector features a PG9 strain relief or 1/2" conduit wire pass through, both with screw terminals for wire connections. The MINI accommodates wire from .240" to .410" diameters as a standard with and QWG of 14 maximum. Environment resistance of NEMA 4/IP 65 along with versions which are CSA approved ensure long trouble free service. Current maximum of 10 Amps and the temperature rating of -40° to +125°C encompasses most applications. The standard interface is an industry standard.Series 5000 MINI Specifications and Options ISO ConnectorCanfield Connector's Series 5000 ISO size connector connects solenoid valves using the DIN 43650 form "A"/ISO 4400 specification. This standard permits industry interchangeability and has been embraced by the solenoid valve industry world-wide. Features include the ability for the user to wire the connector into existing installations or the connector can be wired at the factory. Wire connections are made inside the connector housing and the wire inlet is either PG9, PG11 or 1/2" conduit. Canfield has added to this line with the HT (High Top) housing. The HT accommodates the user with more room for larger wire diameters. The standard ISO connectors are still available for those applications with space constraints. Maximum current rating is 10 amps with a maximum conductor size of 14 AWG with an outer jacket not to exceed .410 inches diameter. There are CSA/NRTL approved versions as well as versions with indicator lights depicting the "on" state. The connectors are NEMA4 and IP 65 environment rated.Series 5000 ISO Specifications and Options SUB-MICRO ConnectorCanfield Connector's Series 5000 Sub-Micro size connector is made to connect solenoid valves using the DIN 43650 form "C"(8 pin center) and the industry standard 9.4mm pin center. These standards permit industry interchangeability and has been embraced by the solenoid valve industry world-wide. Features include the ability for the user to wire the connector into existing installations or the connector can be wired at the factory. Wire connections are made inside the connector housing and the wire inlet is either PG7 or 1/2" conduit. Maximum current rating is 6 amps with a maximum conductor size of 20 AWG with an outer jacket not to exceed .260 inches diameter. There are versions with indicator lights depicting the "on" state. The connectors are NEMA4 and IP 65 environment rated.Series 5000 Sub-Micro Specifications and Options |
|
|
Series 5K Molded Mini and ISO ConnectorsThe Canfield Series 5K molded DIN solenoid valve connectors incorporate the same quality as Canfields' Series 5000 connectors but features a completely molded design. The 5K's low profile and straight wire outlet permit fast and sure electrical connection to any solenoid valve with the standard MINI or ISO interface. The 5K also features indicator lights and internal surge suppression in different versions.Series 5K Specifications and Options |
|
|
Series P5600 Micro Protective Connector (MPC)The Micro Protective Connectors are available in standard MINI, DIN 43650/ISO 4400 Form "A" and Sub-Micro 8mm/DIN 43650 Form "C" and 9mm. The Canfield Connector MPCs provide electrical controllers surge suppression against voltage spikes caused by the solenoids used on hydraulic and pneumatic solenoid valves. Advantages of suppression are:
|
|
|
Series L5000 DIN Connectors with Special Purpose CircuitsCanfield Connector's L5000 Series incorporates circuitry to accommodate a variety of unique applications found in automation. Designed to fit any product with a male DIN 43650 Form "A" interface, the L5000 Series is available in either the standard compact or new HT housing, designed with more space for easier wiring. All circuits are designed to enhance any application by reducing installation times and simplify troubleshooting. Examples of circuits include a load indicator that lights green when all is well and lights red if a connection is broken. There are also a number of circuits that indicate the logic state of pressure switches. The L5000 is built to NEMA 4/IP 65 environment resistance and accommodates wire from .240 to .410 inches diameter in different versions.Series L5000 Specifications and Options |
|
|
Model MCC Multiple Control ConnectorThe Canfield Connector MCC is a cable distribution connector which is available in three different circuit types to control multiple devices from a single inlet 3 + ground connector. The MCC works like a standard connector (DIN 43650 Form A/ISO 4400) but comes with a male inlet, female DIN outlet and has an additional outlet used for either simultaneous control or independent control of a solenoid valve or other external device. The compact design comes pre-wired and is ready to install. Common uses for the MCC include control of double solenoid valves or control of multiple valves with a single input and control cable. The environment resistant quick connect design offers ease of installation and sped of repair for solenoid valve installations.Series MCC Specifications and Options |
|
|
Series FAC Fieldbus to Solenoid Valve AdaptersThe FAC series connectors are modular interface connectors made to conform to industry standard configurations. These connectors interface female ISO (DIN 43650 Form "A"), MINI, Sub-Micro 9mm and Sub-Micro 8mm (DIN 43650 "C") solenoid connections to automobile industry standard male 7/8" (Mini) and 12mm (Micro) circular connectors. These rugged modular connectors offer rapid installation and environmental protection designed to IP65 and NEMA 4. Options include indication LED, surge suppression and various pre-wired circuit configurations to connect with popular multi-port electronic interconnection systems and field-bus systems.Series FAC Specifications and Options |
|
|
Series iLW Interposed Lighted WafersThe Canfield Interposed Lighted Wafer is an electronic, state of the art lighting module designed to install between a DIN type coil and the mating connector. Utilizing SMT (Surface Mount Technology), the iLW's ultra-thin design and high luminescence Gallium Arsenide LEDs enable the lighted wafer to retrofit existing applications or to be used in conjunction with unlighted connectors. Designed to "sandwich" between the connector and the coil, the iLW seals from dust and moisture. The iLW can be installed several times without degradation of the contact surface and is not polarity dependent.Series iLW Specifications and Options |
|
|
Series DCP DIN Coil ProtectorsThe Canfield Connector DCP coil pin protectors are low cost replacements for solenoid connectors that ensure protection of solenoid terminals during shipping and handling. They can also be used to protect spade style terminals on a variety of other products. DCPs are available in a host of colors, styles and available with special logo markings to match the application, the DCP can reduce costs. Constructed of low cost yet rugged polymers, the DCP adds aesthetic appeal and advertising value to the solenoid valve. There is a DCP available for ISO, industry standard MINI, Sub-Micro, and dual spade hydraulic coils.Series DCP Specifications and Options |
|
|
Series M5 Male ConnectorsCanfield Male Connectors are used as electrical quick disconnect interfaces for pneumatic and hydraulic valves and sensors. They are available in standard MINI, DIN 43650 / ISO 4400 form "A" and "B", Sub Micro 8mm, and conduit arrangements. Some Male Connectors are available with 2 + ground or 3 + ground terminal options. Available formats are:
|
|
|
Series R5000 Rectified ConnectorsCanfield Connector's R5000 Series are solenoid valve connectors incorporate full-wave bridge rectifiers inside the DIN 43650 form "A" ISO and MINI connectors. This standard permits industry interchangeability and has been embraced by the solenoid valve industry world-wide. The R5000 converts alternating current to direct current which gives the user an advantage of no coil burnout due to valve sticking creating a high inrush. Also direct current eliminates AC "hum" inherent to alternating current. Features include the ability for the user to wire the connector into existing installations or order the connector prewired at the factory. Wire connections are made inside the connector housing and the wire inlet is either PG9 strain relief, 3/8" or 1/2" conduit. The R5000 has a maximum current rating of 1 amp continuous with maximum wire gauge diameter of 14 AWG. An indicator light is offered for instant diagnostics and to aid setup and installation.Series R5000 Specifications and Options |
|
|
Series D5400 Micro Solenoid Driver (MSD)The Canfield Connector Series D5400 Micro Solenoid Driver is a NEMA 4 DIN 43650 Form "A" and MINI type connector with a built in electronic circuit used to induce solenoid pull-in and reduce holding current. The time proven MSD has been designed into many applications where heat build-up occurs which reduces operating efficiency and life span of solenoid valves. The MSD has two main functions: one is to induce faster or stronger than usual response times at solenoid pull-in, the second is to reduce the net wattage of the solenoid during hold-in. The MSD drives the coil with a high input voltage for a fixed time period until the coil has shifted at which time the MSD reduces the holding voltage, which saves power, and the solenoid runs cool. The MSD is often used to replace low voltage power supplies where a 24 VDC solenoid valve can then be operated by 120 VAC. The Alternating current is rectified and the duty cycle reduced so as to operate the valve at proper voltage and wattage ranges. An additional advantage can be found where the MSD drops the holding voltage, which then reduces heat and current requirements.Series D5400 Specifications and Options |
|
|
Series 5500 Micro Latching Connector (MLC)The Canfield Connector Series 5500 MLC is a solid state toggling/latching relay incorporated inside a MINI or DIN 43650/ISO 4400 form "A" solenoid connector. This device performs a logic function simulating a sustaining push button switch (push-on, push-off) creating a double solenoid type latching effect with single solenoid valves. The MLC can be controlled by either a mechanical remote switch or by a logic signal. The pole defaults to the "off" position should there be a loss of power.Series 5500 Specifications and Options |
|
|
B-Type Round Connectors for SensorsThe Canfield Connector B-Type Round Connectors are intended primarily for use with Canfield proximity devices like the Series 7000 and Series 9000 reed and magnetic cylinder sensors. Types available are:
|
|
|
D-Box Distributor Box for Use with Canfield Round ConnectorsThis electrical Distributor Box (D-Box) is designed to reduce installation and troubleshooting time. Using 8mm, 8mm/12mm, or 12mm quick connect cables, the D-Box is epoxy encapsulated for harsh environments. Computerized controls can be quickly and efficiently connected to sensors and actuators at the machine level using the features of the D-Box.Series D-Box Specifications and Options |
|
|
Series 5950 Micro Proportional Driver (MPD)The Micro Proportional Driver is a compact electronic circuit built into an environment-resistant (NEMA 4) miniaturized enclosure. The circuit features control of proportional solenoids and operators. Functions include minimum and maximum current limiting, control signals from 0-10 V or 0-20 mA (with a step function at 0.2 volts or 0.4 mA included for minimum current), a 0.10-20 seconds linear ramp up/ramp down adjustment and output current proportional to input command signal.This unit incorporates the DIN 43650/ISO 4400 Form "A" connector male and female interface and is mounted by use of a single mounting screw, DIN connector and two gaskets. The MPD is made from engineered polymers for resistance to harsh chemicals and ingress of water or foreign substances. Adjustments are made on the top surface of the unit. The unit can control any proportional solenoid valve operating within the values specified below using variable pulse width modulation. Series 5950 Specifications and Options |
|
|
Series B5950 Block Micro Proportional DriverThe Block Micro Proportional Driver is a compact electronic circuit built into an epoxy potted enclosure designed to control linear proportional solenoid operators. Features include selectable control signal inputs from 0 - 5 V or 0 - 20 mA with adjustable minimum/maximum current output. The output steps to the minimum current setting when 0.1 volts or 0.4 mA is applied to the control signal input. Also included in the compact package is a 0.1 - 20 second adjustable ramp-up and ramp-down output and sine wave dithering (PWM) with adjustable amplitude and frequency. The B5950 has an output current that is proportional to the command signal input.Series B5950 Specifications and Options |
|
Flo-Products Home
Electronic Products